We are providing this guide to facilitate setting up your Wash Box. Please read these instructions completely before starting to assemble your WASH BOX, then refer to diagram #1 for ease of set up and reference to the labeled parts.
As you unpack, please make sure you have all the parts listed.
1. Housing Wrench 6. Chlorine Free Filter
2. Nozzle 7. Iron Free Filter
3. PVC Hose (none for the WB-6T) 8. Abrasive Free Filter
4. Flow Regulator (none for WB-6T) 9. Spot Free Filter
5. Water Test Kit
Assembly and Setup
Place The Wash Box so that the water inlet is on your left, because water in our system flows from left to right.
Using the housing wrench (included) loosen, unscrew and remove all 4 of the filter housings. You may need to flip the wrench over in order to loosen the filter housings. NOTE: After removing the housings, look inside each filter housing and near the top edge you will see a black “O” Ring. Be sure this “O” Ring is seated properly to make a good watertight seal
Take all four of your filters out of the box which are labeled Number 1 – 4. This is the order from left to right in which they will be installed. Each one should only be unwrapped as you install the filter inside the housing.
Unwrap the filter labeled #1 – which is the chlorine free filter. At the top, it has a white rubber gasket that looks like a large washer. Make sure the gasket is seated properly. Place this filter inside the filter housing labeled #1 and install the housing on your WASH BOX by screwing it into the position furthest to the left. See: diagram #1. Hand tighten, then snug it up with the housing wrench. DO NOT over tighten or it may be a problem to remove.
The next step is called purging. Hook up your garden hose to the water inlet. With #1 filter housing installed (per above) turn the water supply on for two seconds then turn off. Repeat this procedure 3-4 times until the water coming out is completely clear to make sure you have flushed all of the filter media dust out of the filter.
Next unwrap the filter labeled #2 – which is the iron free filter. Inspect the gasket, then place the filter inside the filter housing labeled #2 and install it in the 2nd position, from left to right. See Diagram #1. Hand tighten, then snug it up with the housing wrench. DO NOT over tighten. Repeat Purge procedure per above.
Next unwrap the filter labeled #3 – which is the abrasive free filter. Place this filter inside the filter housing labeled #3. Make sure the filter is centered in the housing, then install in the 3rd position, from left to right. See Diagram #1. Hand tighten, then snug it up with the housing wrench. DO NOT over tighten. You DO NOT have to purge this cartridge.
Now unwrap the filter labeled #4 – which is the Spot free filter. Inspect the gasket then place the filter inside the filter housing labeled #4 and install it in the 4th position, from left to right. See Diagram #1. Hand tighten, then snug it up with the housing wrench. DO NOT over tighten.
This next step is very IMPORTANT. Locate the “pressure/flow” regulator (part #4 on list) and install it on the water outlet – right hand side (see Diagram #1) of The Wash Box, to regulate the amount of water flowing through the filters. (NOTE: not part of WB-6T Box). The time that the water spends in contact with the filter media inside the filter cartridges is very important, so please DO NOT remove the “pressure/flow” regulator or try to speed up the water flow.
Attach the PVC hose provided (or your own hose) to the water outlet right hand end of The Wash Box along with the hose nozzle (provided) and you are ready to use it. KEEP IN MIND that the hose you use on the outgoing side of The Wash Box is full of purified water, so you may want to use the shortest length hose (with a smaller diameter) that is appropriate for your specific cleaning job in order to minimize waste of purified water when you drain the hose and put it away.
You now can wash, rinse and walk away; no need to dry any longer.